8.1
www.sunnen.com
ADAPTERS & OTHER
ABRASIVES & TOOLING
MACHINE
ACCESSORIES
GAGING HONING FLUIDS
& COOLANTS
TECHNICAL DATAFILTERS
8.1
ADAPTERS & OTHER
ABRASIVES & TOOLING
GAGING HONING FLUIDS
& COOLANTS
TECHNICAL DATAFILTERS
MBB/MBC/EC/ML Series
EC-6550A Runout Indicator
For EC, ML, KGM Machines
MBC-400A Runout Indicator
For MBB/MBC Machines
KKN-100 Honing Fixture
A precision fixture for use when
honing very short holes - where
diameter of bore is more than three
times the length, and the part has a
flat face. Permits honing parts that
otherwise are too short to be stabi-
lized on the honing tool. Order face
plates separately. Recommendation
of Sunnen Field Engineer is suggested. Fits MBB-1650 and later models.
Shipping Weight: 35,7 kg (78.5 lbs.)
Accessories for Square Honing on Power-Stroked Machine
KKN-615A Flex Pad can be used to hold part tight against faceplate.
KKN-265A Lineup Faceplate may be ordered for use as a fixture
component.
EC-7100 Square Honing Fixture
This fixture is similar to the universal honing fixture which is supplied
with the EC and ML Machines. The fingers move in the same scissors
type motion as on the universal fixture. Also, the fingers automatically
hold the workpiece against the face plate with the start of the honing
cycle and release at the end.
Accessories for Square Honing on ML Machine
EC-7150 Square Honing Conversion Kit:
This fixture kit will convert the standard universal fixture to the EC-7100
Square Honing Fixture.
EC-7080 Faceplate Mounting Kit:
The Mounting Kit consists of the parts required to fasten and adjust the
faceplates on the stroker carriage. This new finger knob design allows
for faster and easier adjustments of the faceplates. A mounting kit may
be purchased for each faceplate to make changing setups faster.
EC-7000 Series Faceplates:
The EC-7000 Series Faceplates are a set of thirteen faceplates covering the
same range as the KKN Faceplates. The faceplate numbers are as follows:
EC-4500 Optional Automatic Size Control Unit
For EC & ML Power-Stroked Honing Machines
The EC-4500 automatic size control unit attaches quickly and easily to
ML honing machines. Features automatic positioning which moves the
probe into position at the beginning of the honing cycle and retracted
at the end of the cycle so that a new workpiece can be installed. Uses
standard A.S.C. probes. (See page 8.4)
Shipping Weight: 52 kg (11 lbs.)
MB-2333A Extra-Long Offset Torque Bar
584 mm (23") Long
Useful for absorbing torque on workpieces which are too long for the
standard 330 mm (13") torque bar. Easy to install in seconds.
Shipping Weight: 2,04 kg (4.5 lbs.)
Loop-Grip Holding Fixtures
Especially useful for hard-to-hold parts such as thinwall tubes,
glass barrels, valve spools, small parts with smooth sur-
faces, and parts with sharp projections such as milling cut-
ters. A must for absorbing torque on most Power
Stroker jobs. Uses emery cloth to
grip the part securely without
distortion. Parts can be inserted
and removed easily. Fixture handle
rests on torque bar to absorb honing
torque and reduce operator fatigue. Each
fixture handles diameters as shown in chart
(let out loop as needed).
KKN-980 and KKN-990 Gimbal Fixtures
The Sunnen KKN-980 and KKN-990 Gimbal Fixtures
attach to the Power Stroking Arm of any Sunnen
Power Stroked Honing Machine. Used with a cus-
tomer manufactured workholding fixture. Allows
the workpiece to float freely on the mandrel, absorb
torque, and provides ease in loading and unloading
fixture. Refer to the following chart for workholding
fixture design.
Fixture Part
Number
Includes
,9 m (3 ft.)
of emery cloth
Model Maximum
Workpiece
O.D.
Ring
I.D.
Maximum
Workholder
O.D.
Maximum
Pivot Pin
Length
Pivot Pin
O.D.
For
Emery
Cloth
Width
Minimum
Dimensions of
Parts to be Honed
Replacement
Emery Cloth
7,6 m
(25 ft.
Length)
mm in. mm in. mm in.
HF-75
HF-200
HF-300
HF-355
19,0
50,0
76,2
12,7
50,0
76,2
1/2
2
3
3,1
9,5
19,0
1/8
3/8
3/4
HF-110
HF-210
HF-310*
3/4
2
3
Length
Outside
Diameters
Set of all three fixtures above.
All others 240 Grit.
* NOTE: HF-320 Heavy Duty Abrasive Cloth 7,6 m (25 ft. length) is available for use
in the HF-300
Holding Fixture and must be ordered separately. 120 Grit is more
tear resistant and is suggested for those applications which use higher pressure
control settings on the honing machine or where the rough hole in the workpiece
makes the heavy duty cloth more desirable.
mm in. mm in. mm in. mm in.mm in.
KKN-980
KKN-990
36,5
57,2
49
70
1 15/16
2 3/4
46
66
6,5
6,5
5
5
3/16
3/16
1/4
1/4
1 13/16
2 5/8
1 7/16
2 1/4
Accessories and Supplies
EC Series Faceplates for
EC-ML Honing Machines
Faceplate
O D
Faceplate
I D
Faceplate
Number
mm in. mm in.
9,2
10,0
12,0
15,0
19,0
24,0
29,5
37,0
44,2
53,0
63,0
71,6
81,0
.362
.398
.472
.590
.750
.945
1.160
1.457
1.740
2.087
2.480
2.820
3.190
.216
.248
.307
.394
.528
.670
.843
1.060
1.300
1.570
1.880
2.220
2.590
5,5
6,3
7,8
10,0
13,4
17,0
21,4
26,9
33,0
39,9
44,7
56,3
65,7
EC-7001
§
EC-7002
§
EC-7003
§
EC-7004
§
EC-7005
§
EC-7006
§
EC-7007
§
EC-7008
§
EC-7009
§
EC-7010
§
EC-7011
§
EC-7012
§
EC-7013
§
NOTE: Request Product Bulletin
#P-1153I on how to modify an
EC Style Faceplate to fit the
MBB & MBC Honing Machines.
§
NOTE: When ordering Faceplates for
use on Precision Honing Machines,
order one EC-7080 Square Honing
Faceplate Mounting Kit and one KKN-
260A Indicator Support Bar. (Only
one Kit and Indicator Support Bar is
required for all EC-7000 series face-
plates. An EC-7080 Kit may be ordered
for each faceplate, to make changing
setup of faceplates on stroker carriage
quicker).
MACHINE
ACCESSORIES
(14 Seiten)
(14 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern